Release Notes

Product: DXFP-RX-4K60
Description: DXLink 4K60 HDMI Fiber Receiver Module

FG#: FG1010-565-01 
     FG1010-565-02 (TAA)

File Name: SW1010-565-0X_DXFP-RX-4K60_1_8_0
Release Date: 5/5/2022
Firmware Version: v1.8.0

1. Prerequisites
2. Features added in this release
3. Fixes in this release:
4. Known Issues
5. Programming Information
6. Notable Points

----------------------------------------------------------
1. Prerequisites
----------------------------------------------------------

- Directly connected DXFP-TX-4K60 v1.7.1 (or later)
- Enova DGX 800/1600/3200/6400 Switcher FW v3.8.13 (or later)
- Enova DGX 100 Series Controller FW v1.8.90 (or later)
- NetLinx Studio v4.3.1519 (or later)

----------------------------------------------------------
2. Features added in this release:
----------------------------------------------------------
-  None

----------------------------------------------------------
3. Fixes in this release:
----------------------------------------------------------
 - Fixed Set Connection to Controller to support changing ICSP Port Number and URL hostname
 - Fixed Standalone webgui issue to allow changing Static IP and default Gateway together
 - Corrected issue causing IR File to be erased on upgrade (IR file should remain on subsequent upgrades) 
 - TX/ RX to change Eth0 default fallback to prevent conflict with DGX IO card IP scheme
  
 Fixed in previous release v1.7.6
 - Fixed issue that could cause TX/RX to go offline or not come back online after reboot or upgrade 
 - Improved Set Connection to allow changing ICSP Port Number and use URL hostname (Note: Don't use "-" in hostname)
 - Improved ICSP LED-DIS/LED-EN function to match legacy DXLink endpoint behavior
 - Corrected issue with certain 4K reolutions (at 59.94Hz YCbCr 4:2:0) where switching sometimes resulted in a blue screen
 - Improved IR function, added support to upload IR HEX Code for IR Local control by user on TX/RX WebGUI
 - Added ICSP commands "LOG_RTC-YYYY/MM/DD hh:mm:ss" / "?LOG_RTC"to set/get real time clock on TX/RX

Fixed in previous release v1.7.1
 - Fixed issue where sending RXCLR would require reboot to send other commands
 - Fixed problem where DVI HDCP1.4 signal through TX-RX pair results in snow after 
   hotplug of HDMI cable
 - Improved ID button functionality to match expected results as outlined in manual
 - Improved how TX WebGUI pages get refreshed when connection mode changes
 - Fixed "No Video" issue for RX after hotplug or power cycle when connected to DGX or DVX



----------------------------------------------------------
4. Known Issues
----------------------------------------------------------
- When scaler is set to BYPASS, some image settings on the web interface are invalid
 
----------------------------------------------------------
5. Programming Information
----------------------------------------------------------
 - These devices can be updated using a VNM (Virtual Netlinx Controller)
   but the update will go much faster if you can connect to a physical
   Netlinx controller. VNM update could take up to 2 hours but
   using a physical controller should take less than an hour.

----------------------------------------------------------
6. Notable Points
----------------------------------------------------------
 - PLEASE READ the Quick Start Guide in regard to the DIP switches located 
   on the DXLink 4K60 Receiver before attempting to connect to the network.

 - These units have a web interface that is accessible in by entering
   the URL of the device into a web browser. This may indicate there
   is a certificate error, but you can select the Advanced option at
   the bottom and proceed to the page. A new certificate can be loaded
   via the web interface.

 - This web interface is only available when connected to a DXLink 4K60 Fiber Transmitter.
   It is disabled when connected to a switcher.

 - This device has a default static IP: 192.168.1.2 when it isn't assigned a dynamic IP
   by DHCP server or auto-setup porcess.