Release Notes

DXLink Fiber Receiver Firmware (Enova DGX 100 Series
Compatible)

!! IMPORTANT: Scaler settings upgrade warning
!!
!! If upgrading to DGX firmware v3.0.2x from v3.0.10,
!! and if DXLink RX are configured with non-default
!! scaler settings (scaling mode, aspect ratio and
!! manual resolution), the "PERSISTAV" ICSP command
!! must first be sent to those RX's before performing
!! the firmware upgrade of either the DGX or the RX's
!! in order to preserve their modified settings.

!!This firmware version requires Enova DGX 100 Series
compatibility on connected Enova DGX systems!!

!!!Please reference the Enova DGX Board and Endpoint
Compatibility Instructions on the AMX.com product
page for more information!!!

FG#:

FG1010-560 (DXF-RX-SMD, DXLink HDMI Single Mode Fiber Receiver, Duplex)
FG1010-561 (DXF-RX-SMS, DXLink HDMI Single Mode Fiber Receiver, Simplex)
FG1010-562 (DXF-RX-MMD, DXLink HDMI Multimode Fiber Receiver, Duplex)
FG1010-563 (DXF-RX-MMS, DXLink HDMI Multimode Fiber Receiver, Simplex)


Release Date: 2016-06-02
Current Released Firmware: v1.4.17
SW1010_56x_AVB_KIT_DXLF_RX_v1_4_17.kit

----------------------------------------------------------
Table of Contents
----------------------------------------------------------

1. Prerequisites
2. Features added in this release
3. Fixes in this release
4. Notable points
5. Programming information

----------------------------------------------------------
1. Prerequisites
----------------------------------------------------------
- DXF-TX-xxD v1.4.9 (or later) to support standalone
  configuration.

- Enova DGX DXLink Fiber I/O boards must be upgraded to the
  latest firmware versions (as provided in the DGX kit file
  listed below).

- Enova DGX 100 Series enclosures need Enova DGX
  800/1600/3200/6400 FW v3.0.20 (or later) and Master FW:

    - SW1060_Master_v1.4.72 (or later)

- Enova DGX 8/16/32/64 enclosures need Enova DGX 8/16/32/64
  FW v2.2.8 (or later) and Master FW:

    - SW1056_Master_v4_2_395.KIT or later (NI-Series)
      Shows in Online Tree as "NI Master"

    - SW2106_NX-X200_Master_v1_3_110.kit or later (NX-Series)
      Shows in Online Tree as "DGX Master"

- NetLinx Studio v4.3.1519 or later

- DGX Configuration Software v1.0.6 or later

----------------------------------------------------------
2. Features added in this release (since v1.4.15)
----------------------------------------------------------
- Add ICS LAN port public/private control when
  connected to a DGX through the new 5002 device
  ENDPOINT_RX_ICSLAN_PORT-Public|Private command.

----------------------------------------------------------
3. Fixes in this release (since v1.4.15)
----------------------------------------------------------
- Fix handling of value 0 for VIDOUT_SLEEP_DELAY.
  When set to zero, the display will now immediately
  be put to sleep when there is no upstream video.

- Fix orange screen after DGX reboot when using
  certain displays.

----------------------------------------------------------
4. Notable points
----------------------------------------------------------
-  IMPORTANT: Scaler settings upgrade warning
   If upgrading to DGX firmware v3.0.2x from v3.0.10,
   and if DXLink RX are configured with non-default
   scaler settings (scaling mode, aspect ratio and
   manual resolution), the "PERSISTAV" ICSP command
   must first be sent to those RX's before performing
   the firmware upgrade of either the DGX or the RX's
   in order to preserve their modified settings.

- On duplex devices, if DIP switch 4 is set ON, the device
  will be put into unidirectional mode.  This will make the
  duplex device act similarly to a simplex device.
  Ethernet and control over the fiber link will be disabled.
  See the instruction manual for details.

- Please read the documentation in regard to the DIP
  switches located on the bottom of the Tx/Rx modules
  before attempting to connect to the network.

- After a FACTORYAV (ICSP) or RESET FACTORY (telnet)
  command, a reboot of the endpoint is required.

- The RX module uses these solid color screen indications:

  ORANGE
    Indicates an HDCP authentication failure with
    the connected HDMI sink (monitor or other device).

- If using a hostname in the USB_HID_ROUTE command,
  the hostname length is limited to 50 characters.

----------------------------------------------------------
5. Programming information
----------------------------------------------------------

- DXLink Fiber Receiver Firmware (Enova DGX 100 Series
  Compatible)

- !!This firmware version requires Enova DGX 100 Series
  compatibility on connected Enova DGX systems!!

- !!!Please reference the Enova DGX Board and Endpoint
  Compatibility Instructions on the AMX.com product
  page for more information!!!
