Product Name: MVP-9000i - 9" Modero ViewPoint Wireless Touch Panel with Intercom

FG#: FG5967-01 (MVP-9000i black)
     FG5967-02 (MVP-9000i white)

Current Firmware Version: 2.86.62
Release Date: 01/30/2013
Device ID: 0x157

Prerequisites: 
Master FW capable of hotswapping build 439 or later
TPDesign4 3.0 build 634 or later.
Intercom module v1.9 or later.
SIP module 2.11 or later
TDS/WDS Firmware 1.10.6 or later

Changes in this release
-----------------------
-- Fixed an issue with momentary feedback not showing up due to drawing delays
-- Fixed an issue where long presses(> 30 seconds) would cause the device to reboot
-- Fixed an issue with VPN connections not working
-- Fixed an issue with short presses of IR control not registering
-- Fixed an issue with the backlight not turning all the way off
-- Added more detail to the custom events used when querying button information(font, justification, etc)
-- Fixed the ability to erase wireless certificates
-- Improved SIP stability
-- Greatly improved battery management
--    Added the ability to recalibrate the battery for improved accuracy
--    Added battery usage modes to allow a choice between battery runtime and lifetime
--    Added Battery Test feature


Known Issues
------------
DOCK AND UNDOCK:
-- If a panel is docked, any loss of network connectivity on the wired interface
   (such as a connected switch going down) may lead to unexpected issues like one way
   voice or inability to connect to remote servers (e.g. for SIP, dynamic images).
-- If the wired interface will not be used (in other words, the docking station is
   is being used for storage and charging only), the Wired network settings
   should be left at their factory defaults (DHCP).

TABLE DOCK LATCH:
-- When the panel is removed from a dock with the Table Dock Latch set to "off"  
   it will take longer for the panel to reconnect wirelessly than usual.
   The panel waits for the master to timeout the device number, and then reconnects to the
   master with the same device number.  With non-encrypted ICSP, the panel 
   disconnects and reconnects to a master in about 3-4 seconds. Encrypted ICSP will take 
   around 15-20 seconds to reconnect. It is recommended not to use wired ethernet if the 
   panel is set to forced undocks to avoid the transition time between wired and wireless modes.

USB:
-- TPD4 file with wrong resolution can be downloaded.
-- OTG USB host is sometimes not recognized upon plugging in. Unplugging and replugging should fix.

POWER MANAGEMENT:
-- Sleep cannot be disabled and a non-zero value for sleep timeout must be set. The default value is the 
   maximum value of 2 hours.
-- The panel cannot enter full standby mode if there is a USB device plugged in or MicroSD card inserted.

INTERCOM AND DYNAMO:
-- When the panel is connected wirelessly (particularly with a weak signal) and streaming audio and video with 
   a MET-ECOM, the video rate may slow to a few frames per seconds.  This can cause the MET-ECOM to
   send bad frames which can lead to occasional video freeze and one-way or no audio.

IP:
-- If a Static IP is set on the wired (or wireless) settings in the same subnet range as the USB 
   (172.16.x.x), the gateway populates with 255.255.255.255. This is only cosmetic and does not impact the 
   performance

WIRELESS:
-- The roaming/band changes may cause the panel roaming settings to change during the upgrade process, 
   double check the roam settings after upgrading if you are using active roaming.

PROGRAMMING INFORMATION:
-----------------------
After upgrading you MUST resave wireless settings.  You do not have to reenter the settings. 
Open wireless page and press save.

Band Selection: Note - The band selection will effect what you see when doing a site survey.
802.11a/b/g -> A and B bands, all channels
802.11b/g -> B band, channels 1,6,11
802.11a -> A band, all channels

Active roaming:
Disabled -> Roaming is passive, and will only occur when the panel loses connection to its current access point
Enabled -> The panel is actively looking for better access points to roam to.
