The BLU-805 has all the features of the BLU-800 but has the addition of an AVB card for AVB audio transport.
Name: The name of this item
Class Name: The type of this device
Device ID: The ID number of this device
BLU link sync: The sync source for the BLU link digital audio bus. Default, Sync to BLU link or sync to BNC
Sample Rate Pulldown: Sample rate pulldown frequency when an external sync source is being used
Sample Rate: Offers changing the sample rate from 48kHz to 96kHz and vice-versa
Acknowledge (ACK): Set to 'yes' to inform the London device that is should expect acknowledgement of the messages being sent.
Baud Rate: Drop-down selection for the Baud Rate
Data Bits: The number of bits for data
Parity: The parity
Stop Bits: The number of stop bits
Dynamic Meters: The number of Dynamic Meters to use in this device. Hover the cursor over a wire in the design while online and a Dynamic Meter displays the signal level.
Logic Change Block: If enabled, only Logic Sources and Ends will be written to the change block. Only enable if there are performance issues with logic.
Logic Subscription: If enabled, only Logic Sources and Ends will be subscribed to. Only enable if there are issues with logic.
Recall Presets on Startup: When enabled, presets assigned to control ports will be recalled when the device is powered on.
Control Port Subscribe: When enabled, force control ports to subscribe to controlled parameters.
Front Panel Led Indicators:
Per Input: Signal Present, CLIP, SYNC/48V, I/O card type (IN, OUT, DIG, AEC)
Other: LCD Display, Master, Network Link active, Data Activity
Analog Inputs:
Up to 16 electronically balanced on Phoenix Combicon removable screw connectors
Mic/Line Inputs: Nominal gain 0dB, electronically switchable up to +48dB,in +6dB steps
Input Impedance: 3.5kΩ
Maximum Input Level: +20dBu with 0dB input gain,+8dBu with 12dB gain
CMRR: >75dB at 1KHz
Input Noise (E.I.N.): <-128dBu typical with 150Ω source
Phantom Power: 48V nominal, selectable per input
A/D Latency: 38.7/Fs
Digital Inputs:
Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors
Input Impedance: 110 ohm (AES/EBU), 75 ohm (S/PDIF)
Sample Rate: 48kHz or 96kHz
Sample Rate Conversion: 32kHz-96kHz
THD+N: <-140dB
Latency: 3/Fso + (56.581/Fsi) + (55.658/Fso)
Analog Outputs:
Up to 16 electronically balanced on Phoenix/Combicon removable screw connectors
Maximum Output Level: +19dBu
Frequency Response: 20Hz-20KHz (+0.5dB/-1dB)
THD: <0.01% 20Hz to 20KHz, +10dBu output
Dynamic Range: 108dB typical, 22Hz-22KHz unweighted
Crosstalk: <-75dB
D/A Latency: 28/Fs
Digital Outputs:
Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors
Output Impedance: 110 ohm (AES/EBU), 75 ohm (S/PDIF)
Sample Rate: 48kHz or 96kHz
Sample Rate Conversion: 32kHz-96kHz
THD+N: <-140dB
Latency: 3/Fso + (56.581/Fsi) + (55.658/Fso)
Control Ports:
12 inputs and 6 outputs
Control Input Voltage: 0 to 4.5v
Control Input Impedance: 4.7kΩ to +5V (2-wire mode), >1MΩ (3-wire mode)
Logic Output Voltage: 0 or +5V unloaded
Logic Output Impedance: 440Ωs
Logic Output Current: 10mA source, 60mA sink
Watchdog Output:
Phoenix/Combicon connector for failsafe control
Opto Output Current: 14mA maximum
Withstanding Voltage: 80V maximum (Off)
Series Impedance: 220Ω (isolated)
Control Network:
Connectors: RJ45 Ethernet connector
Maximum Cable Length: 100m/300ft on Category 5 cable between device and Ethernet switch
Digital Audio Bus:
Connectors: 2 x RJ45 Ethernet connectors
Maximum Cable Length: 100m/300ft on Category 5e cable between devices
Maximum Number of Nodes: 60
Latency Per Node: 4/Fs
Ethernet AVB Audio Network:
Connectors: 2 x RJ45 connectors
Maximum Cable Length: 100m/300ft on Category 5e cable between device and Ethernet switch
Power and Dimensions:
Mains Voltage: 100-240V AC, 50/60Hz
Power Consumption: <35VA
BTU Rating: <188 BTU/hr
Operating Temperature Range: 5 (41) to 35 (95) degrees C (degrees F)
Dimensions (H(U) x W x D): 1.75" (1U) x 19" x 12.5" (45mm x 483mm x 318mm)
Weight: 9 lbs / 4.1 kgs (estimated)